+- MMOMinion (https://www.mmominion.com)
+-- Forum: FFXIVMinion (https://www.mmominion.com/forumdisplay.php?fid=87)
+--- Forum: [DOWNLOADS] Addons, Lua Modules, Navigation Meshes.. (https://www.mmominion.com/forumdisplay.php?fid=90)
+---- Forum: Outdated (https://www.mmominion.com/forumdisplay.php?fid=110)
+---- Thread: [Mining] 1 - 50 (/showthread.php?tid=4377)
[Mining] 1 - 50 - Latty79 - 10-18-2013
Please report stucks. Don't know if these locations are the best, but it's what I used to level mining. I didn't add paths to the towns, but they aren't far from them. These aren't used for the mining quests, but I might make meshes for them at some point.
1-5: Central Thanalan - Four Sisters
6-10: Western Thanalan - East Hammer
11-15: Western Thanalan - Copperbell Mines
16-20: Eastern Thanalan - Royal Allagan Sunway
21-25: South Shroud - Upper Paths
26-30: East Shroud - Nine Ivies
31-35: Eastern La Noscea - NW of Costa Del Sol
36-40: South Shroud - South of Goblins' Meet
41-45: Upper La Noscea - South of Camp Bronze Lake
46-50: North Thanalan - SE of Ceruleum Processing Plant
Note: I'm keeping the .obj files as is so you can modify them in case I missed a few mining nodes.
Just noticed Gabi did a similar mesh for the level 25 nodes and woohoo88 did the same for the level 40. I should pay more attention before I post stuff :) Feel free to use theirs as i'm sure they did I better job than I did.
Here are the links to their meshes.
Gabi - http://mmominion.com/Thread-South-Shroud-20-25-Buscarron-s-Druthers
woohoo88 - http://mmominion.com/Thread-Quarrymill-35-40-Mining
RE: [Mining] 1 - 50 - KaWeNGoD - 10-19-2013
Thanks for your work Latty79
RE: [Mining] 1 - 50 - Syther - 10-19-2013
You Sir, earned my respect! Thank you very much for this !!
RE: [Mining] 1 - 50 - psychospectrum - 10-19-2013
Tried these out a bit last night, the 36-40 and 41-45 ones work great, thanks!
RE: [Mining] 1 - 50 - twister - 10-19-2013
Thx works great
RE: [Mining] 1 - 50 - ffffffff - 10-21-2013
46-50 does not work properly in my environment
Does not recognize sometimes the point in the upper right
RE: [Mining] 1 - 50 - inokichi - 10-21-2013
Yeah it dont work properly for me too
RE: [Mining] 1 - 50 - Latty79 - 10-21-2013
I left the .obj so you can fix them yourselves. It's not hard.
RE: [Mining] 1 - 50 - Notahacker - 10-21-2013
(10-21-2013, 10:39 AM)ffffffff Wrote: 46-50 does not work properly in my environment
Does not recognize sometimes the point in the upper right
same issue here it just stops i tried to edit it but no luck the mesh just wont record close enought
Edit: Went to the point and recorded the mesh using the ctrl key and now its all fine
RE: [Mining] 1 - 50 - Latty79 - 10-21-2013
Download 46-50fix on the first post and let me know if it fixed it. I ran it for an hour without any problems.